|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
TS1871-TS1872-TS1874 1.8V input/output rail-to-rail Low power operational amplifiers Features Operating range from VCC = 1.8V to 6V Rail-to-rail input and output Extended Vicm (VDD - 0.2V to VCC + 0.2V) Low supply current (400A) Gain bandwidth product (1.6MHz) High unity gain stability ESD tolerance (2kV) Latch-up immunity Available in SOT23-5 micro package Output VDD Non Inverting Input TS1871ILT 1 2 3 4 Inverting Input 5 VCC TS1871ID/IDT N.C. Inverting Input Non Inverting Input VDD 1 2 3 4 _ + 8 7 6 5 N.C. VCC Output N.C. Applications Battery-powered applications (toys) Portable communication devices (cell phones) Audio driver (headphone drivers) Laptop/notebook computers TS1872IN-TS1872ID/IDT-TS1872IST TS1872IPT Output 1 Inverting Input 1 Non Inverting Input 1 VDD 1 2 3 4 _ + _ + 8 7 6 5 VCC Output 2 Inverting Input 2 Non Inverting Input 2 Description The TS187x (single, dual & quad) is an operational amplifier family able to operate with voltages as low as 1.8V and features both input and output rail-to-rail. The common mode input voltage extends 200mV beyond the supply voltages at 25C while the output voltage swing is within 100mV of each rail with 600 load resistor. This device consumes typically 400A per channel while offering 1.6MHz of gain-bandwidth product. The amplifier provides high output drive capability typically at 65mA load. These features make the TS187x family ideal for sensor interface, battery-supplied and portable applications. TS1874IN-TS1874ID/IDT-TS1874IPT Output 1 Inverting Input 1 Non Inverting Input 1 VCC Non Inverting Input 2 Inverting Input 2 Output 2 1 2 3 4 5 6 7 + _ + _ _ + _ + 14 Output 4 13 Inverting Input 4 12 Non Inverting Input 4 11 VDD 10 Non Inverting Input 3 9 8 Inverting Input 3 Output 3 May 2007 Rev 3 1/27 www.st.com 27 Contents TS1871-TS1872-TS1874 Contents 1 2 3 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 DIP8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 SO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 TSSOP8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 MiniSO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 DIP14 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 SO-14 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 TSSOP14 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 SOT23-5 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 4 5 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2/27 TS1871-TS1872-TS1874 Absolute maximum ratings and operating conditions 1 Table 1. Symbol VCC Vid Vi Tstg Tj Absolute maximum ratings and operating conditions Absolute maximum ratings Parameter Supply voltage(1) Differential input voltage Input voltage Storage temperature Maximum junction temperature Thermal resistance junction to ambient SOT23-5 DIP8 DIP14 miniSO-8 SO-8 SO-14 TSSOP8 TSSOP14 Thermal resistance junction to case SOT23-5 DIP8 DIP14 miniSO-8 SO-8 SO-14 TSSOP8 TSSOP14 HBM: human body model(4) MM: machine model(5) CDM: charged device model(6) Latch-up immunity Lead temperature (soldering, 10 sec) Output short-circuit duration (3) (2) Value 7 1 VDD -0.3 to VCC +0.3 -65 to +150 150 250 85 66 190 125 103 120 100 81 41 33 39 40 31 37 32 2 200 1.5 200 250 see note (7) Unit V V V C C Rthja C/W Rthjc C/W kV V kV mA C ESD 1. All voltage values, except differential voltage are with respect to network terminal. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. If Vid > 1V, the maximum input current must not exceed 1mA. When Vid > 1V, add an input series resistor to limit input current. 3. Short-circuits can cause excessive heating. Destructive dissipation can result from simultaneous short-circuits on all amplifiers. 4. Human body model: A 100pF capacitor is charged to the specified voltage, then discharged through a 1.5k resistor between two pins of the device. This is done for all couples of connected pin combinations while the other pins are floating. 5. Machine model: A 200pF capacitor is charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5). This is done for all couples of connected pin combinations while the other pins are floating. 6. Charged device model: all pins and the package are charged together to the specified voltage and then discharged directly to the ground through only one pin. This is done for all pins. 7. Short-circuits from the output to VCC can cause excessive heating. The maximum output current is approximately 80mA, independent of the magnitude of VCC. Destructive dissipation can result from simultaneous short-circuits on all amplifiers. 3/27 Absolute maximum ratings and operating conditions Table 2. Symbol VCC Vicm Toper Supply voltage Common mode input voltage range Top = 25C, 1.8 VCC 6V Tmin < Top < Tmax, 1.8 VCC 6V Operating free air temperature range TS1871-TS1872-TS1874 Operating conditions Parameter Value 1.8 to 6 VDD - 0.2 to VCC + 0.2 VDD to VCC -40 to + 125 Unit V V C 4/27 TS1871-TS1872-TS1874 Electrical characteristics 2 Table 3. Symbol Electrical characteristics Electrical characteristics at VCC = +1.8V with VDD = 0V, CL & RL connected to VCC/2, and Tamb = 25C (unless otherwise specified)(1) Parameter Conditions Vicm = Vout = VCC/2 TS1871A/2A/4A Tmin Tamb Tmax TS1871/2/4 Tmin Tamb Tmax (2) Min. Typ. Max. Unit Vio Input offset voltage 0.1 1 1.5 3 6 mV Vio Iio Iib CMR Input offset voltage drift Input offset current Input bias current Common mode rejection ratio 20 log (Vic/Vio) Large signal voltage gain Vicm = Vout = VCC/2 Tmin Tamb Tmax 2 3 40 55 52 77 70 1.65 1.62 1.65 1.62 77 30 60 125 150 V/C nA nA dB Vicm = Vout = VCC/2(1) Tmin Tamb Tmax 0 Vicm VCC, Vout = VCC/2 Tmin Tamb Tmax Vout = 0.5V to 1.3V RL = 2k RL = 600 Vid = 100mV RL = 2k RL = 600 Tmin Tamb Tmax, RL = 2k Tmin Tamb Tmax, RL = 600 Vid = -100mV RL = 2k RL = 600 Tmin Tamb Tmax, RL = 2k Tmin Tamb Tmax, RL = 600 VID = 100mV, VO = VDD VID = -100mV, VO = VCC Vout = VCC/2 AVCL = 1, no load Tmin Tamb Tmax RL = 10k CL = 100pF, f = 100kHz , , RL = 10k CL = 100pF, AV = 1 CL = 100pF f = 1kHz 0.9 0.38 20 20 Avd 92 85 1.77 1.74 dB VOH High level output voltage V VOL Low level output voltage 88 115 100 150 100 150 mV Output source current Io Output sink current Supply current (per amplifier) Gain bandwidth product Slew rate Phase margin Input voltage noise Total harmonic distortion 65 mA 65 400 1.6 0.54 53 27 0.01 560 600 A MHz V/s Degrees nV/ Hz % ICC GBP SR m en THD 1. All parameter limits at temperatures different from 25C are guaranteed by correlation. 2. Maximum values include unavoidable inaccuracies of the industrial tests. 5/27 Electrical characteristics Table 4. Symbol TS1871-TS1872-TS1874 Electrical characteristics at VCC = +3V with VDD = 0V, CL & RL connected to VCC/2, and Tamb = 25C (unless otherwise specified)(1) Parameter Conditions Vicm = Vout = VCC/2 TS1871A/2A/4A Tmin Tamb Tmax TS1871/2/4 Tmin Tamb Tmax (2) Min. Typ. Max. Unit Vio Input offset voltage 0.1 2 1 1.5 3 6 mV Vio Iio Iib CMR Input offset voltage drift Input offset current Input bias current Common mode rejection ratio 20 log (Vic/Vio) Large signal voltage gain Vicm = Vout = VCC/2 Tmin Tamb Tmax V/C 30 60 125 150 nA nA dB 3 4 60 57 80 74 2.82 2.80 2.82 2.80 Vicm = Vout = VCC/2 (1) Tmin Tamb Tmax 0 Vicm VCC, Vout = VCC/2 Tmin Tamb Tmax Vout = 0.5V to 2.5V RL = 2k RL = 600 VID = 100mV RL = 2k RL = 600 Tmin Tamb Tmax, RL = 2k Tmin Tamb Tmax, RL = 600 VID = -100mV RL = 2k RL = 600 Tmin Tamb Tmax, RL = 2k Tmin Tamb Tmax, RL = 600 VID = 100mV, VO = VDD VID = -100mV, VO = VCC Vout = VCC/2 AVCL = 1, no load Tmin Tamb Tmax RL = 10k CL = 100pF, f = 100kHz , RL = 10k CL = 100pF, AV = 1 , CL = 100pF f = 1kHz 1 0.42 20 20 80 Avd 92 95 2.95 2.95 dB VOH High level output voltage V VOL Low level output voltage 88 115 120 160 120 160 mV Output source current Io Output sink current Supply current (per amplifier) Gain bandwidth product Slew rate Phase margin Input voltage noise Total harmonic distortion 80 mA 80 450 1.7 0.6 53 27 0.01 650 690 A MHz V/s Degrees nV/ Hz % ICC GBP SR m en THD 1. All parameter limits at temperatures different from 25C are guaranteed by correlation. 2. Maximum values include unavoidable inaccuracies of the industrial tests. 6/27 TS1871-TS1872-TS1874 Table 5. Symbol Electrical characteristics Electrical characteristics at VCC = +5V with VDD = 0V, CL & RL connected to VCC/2, and Tamb = 25C (unless otherwise specified) (1) Parameter Conditions Vicm = Vout = VCC/2 TS1871A/2A/4A Tmin Tamb Tmax TS1871/2/4 Tmin Tamb Tmax (2) Min. Typ. Max. Unit Vio Input offset voltage 0.1 2 1 1.5 3 6 mV Vio Iio Iib Input offset voltage drift Input offset current Input bias current Common mode rejection ratio 20 log (Vic/Vio) Supply voltage rejection ratio 20 log (Vcc/Vio) Large signal voltage gain Vicm = Vout = VCC/2 Tmin Tamb Tmax V/C 30 60 130 150 nA nA 3 70 Vicm = Vout = VCC/2 (1) Tmin Tamb Tmax 0 Vicm VCC, Vout different from VCC/2 Tmin Tamb Tmax VCC = 1.8 to 5V Vout = 1V to 4V RL = 2k RL = 600 VID = 100mV RL = 2k RL = 600 Tmin Top Tmax, RL = 2k Tmin Top Tmax, RL = 600 VID = -100mV RL = 2k RL = 600 Tmin Top Tmax, RL = 2k Tmin Top Tmax, RL = 600 VID = 100mV, VO = VDD VID = -100mV, VO = VCC Vout = VCC/2 AVCL = 1, no load Tmin Tamb Tmax RL = 10k CL = 100pF, f = 100kHz , , RL = 10k CL = 100pF, AV = 1 CL = 100pF f = 1kHz 1 0.42 20 20 65 62 70 CMR 85 dB SVR 90 dB Avd 83 77 4.80 4.75 4.80 4.75 92 85 4.95 4.90 dB VOH High level output voltage V VOL Low level output voltage 88 115 130 188 130 188 mV Output source current Io Output sink current Supply current (per amplifier) Gain bandwidth product Slew rate Phase margin Input voltage noise Total harmonic distortion 80 mA 80 500 1.8 0.6 55 27 0.01 835 875 A MHz V/s Degrees nV/ Hz % ICC GBP SR m en THD 1. All parameter limits at temperatures different from 25C are guaranteed by correlation. 2. Maximum values include unavoidable inaccuracies of the industrial tests. 7/27 Electrical characteristics TS1871-TS1872-TS1874 Figure 1. 160 140 Quantity of pieces 120 100 80 60 40 20 0 -2. Input offset voltage distribution 492 pieces tested Vcc = 5V Temp = +25C Figure 2. 200 Input offset voltage vs. temperature Vcc = 1.8V 150 Input Offset voltage (V) 100 50 0 -50 -100 -150 -40 Vcc = 5V Vcc = 3V -1.6 -1.2 -.8 -.4 0 .4 .8 1.2 1.6 2 -20 0 20 40 60 80 100 120 140 Input offset voltage (mV) Temperature (C) Figure 3. 10.0 Input bias current vs. temperature Vcc = 1.8V Vicm = 0.9V Figure 4. 10.0 Input bias current vs. temperature Vcc = 3V Vicm = 1.5V Input bias current (nA) -10.0 Input bias current (nA) -20 0 20 40 60 80 100 120 140 0.0 0.0 -10.0 -20.0 -20.0 -30.0 -30.0 -40.0 -40 -40.0 -40 -20 0 20 Temperature (C) 40 60 80 100 Temperature (C) 120 140 Figure 5. 600 500 Supply current (A) Supply current/amplifier vs. supply Figure 6. voltage 550 Supply current/amplifier vs. temperature Vcc = 5V 500 Supply current (A) Vcc = 3V 450 400 350 300 250 -40 Vcc = 1.8V 400 300 200 100 0 0 2 4 Supply voltage (V) 6 8 Tamb = 25C -20 0 20 40 60 80 100 120 140 Temperature (C) 8/27 TS1871-TS1872-TS1874 Electrical characteristics Figure 7. 120 Common mode rejection (dB) 115 110 105 100 95 90 85 -40 Common mode rejection vs. temperature Vcc = 1.8V Vicm = 0V Figure 8. 110 Supply voltage rejection (dB) Supply voltage rejection vs. temperature Vcc = 1.8V Vicm = 0V 100 Vcc = 3V Vicm = 0V 90 80 Vcc = 5V Vicm = 0V 70 -20 0 20 40 60 80 Temperature (C) 100 120 140 60 -40 -20 0 20 40 60 80 100 120 140 Temperature (C) Figure 9. 110 Supply voltage rejection vs. temperature Figure 10. Supply voltage rejection vs. temperature 110 Supply voltage rejection (dB) Vcc = 5V Vicm = 0V 100 Supply voltage rejection (dB) Vcc = 3V Vicm = 0V 100 90 90 80 80 70 70 60 -40 -20 0 20 40 60 80 100 120 140 60 -40 -20 0 20 40 60 80 100 120 140 Temperature (C) Temperature (C) Figure 11. Power supply voltage rejection vs. frequency -20 Supply voltage rejection (dB) -30 -40 -50 -60 -70 -80 100 Vcc = 1.8V Vicm = 0.7V Gain = 10 Figure 12. Open loop gain vs. frequency 110 Vcc = 1.8V Vicm = 0.9V Open loop gain (dB) 100 RL = 2 kOhms 90 RL = 600 Ohms 80 1000 10000 100000 70 -40 -20 0 20 Frequency (Hz) 40 60 80 Temperature (C) 100 120 140 9/27 Electrical characteristics TS1871-TS1872-TS1874 Figure 13. Open loop gain vs. temperature 110 Vcc = 3V Vicm = 1.5V Open loop gain (dB) 100 RL = 2 kOhms Figure 14. Open loop gain vs. temperature 110 Vcc = 5V Vicm = 2.5V Open loop gain (dB) 100 RL = 2 kOhms 90 RL = 600 Ohms 90 RL = 600 ohms 80 80 70 -40 -20 0 20 40 60 80 100 120 140 70 -40 -20 0 20 40 60 80 100 120 140 Temperature (C) Temperature (C) Figure 15. High level output voltage vs. temperature 110 Voltage referenced to VCC (mV) RL = 600 ohms 100 90 80 70 Vcc = 1.8V 60 50 40 -40 Vcc = 3V Vcc = 5V Figure 16. Low level output voltage vs. temperature 110 RL = 600 ohms Voltage referenced to Gnd (mV) 100 90 80 Vcc = 3V 70 60 50 40 -40 Vcc = 1.8V Vcc = 5V -20 0 20 40 60 80 100 120 140 -20 0 20 40 60 80 100 120 140 Temperature (C) Temperature (C) Figure 17. High level output voltage vs. temperature 80 Voltage referenced to VCC (mV) 70 Vcc = 5V 60 50 40 30 20 -40 Vcc = 3V RL = 2 kohms Figure 18. Low level output voltage vs. temperature 80 Voltage referenced to VCC (mV) RL = 2 kohms 70 Vcc = 5V 60 50 40 30 20 -40 Vcc = 3V Vcc = 1.8V Vcc = 1.8V -20 0 20 40 60 80 100 120 140 -20 0 20 40 60 80 100 120 140 Temperature (C) Temperature (C) 10/27 TS1871-TS1872-TS1874 Electrical characteristics Figure 19. Output current vs. temperature 100 Isink 50 Vcc = 1.8V Vid = 1V 0 Isource -50 Figure 20. Output current vs. temperature 100 Isink 50 Vcc = 3V Vid = 1V 0 Isource -50 Output current (mA) Output current (mA) -100 -40 -20 0 20 40 60 80 100 120 140 -100 -40 -20 0 20 40 60 80 100 120 140 Temperature (C) Temperature (C) Figure 21. Output current vs. temperature 100 Figure 22. Output current vs. output voltage 100 T = 25 C T = -40 C Isink Output current (mA) Output current (mA) 50 Vcc = 5V Vid = 1V 0 50 T = 125 C Vcc = 1.8V Vid = 0.1V Vicm = 0.9V T = -40 C -50 T = 125 C T = 25 C sink 0 -50 Isource source -100 -40 -20 0 20 40 60 80 100 120 140 -100 0.0 0.5 1.0 Output voltage (V) 1.5 2.0 Temperature (C) Figure 23. Output current vs. output voltage 100 T = -40 C T = 25 C Output current (mA) T = 125 C Vcc = 3V Vid = 0.1V Vicm = 1.5V T = 125 C -50 T = 25 C T = -40 C -100 0.0 0.5 1.0 1.5 2.0 2.5 source 3.0 3.5 sink Figure 24. Output current vs. output voltage 100 T = -40 C sink T = 125 C Vcc = 5V Vid = 0.1V Vicm = 2.5V T = 125 C -50 T = 25 C T = -40 C -100 0.0 1.0 2.0 3.0 Output voltage (V) 4.0 source 5.0 T = 25 C 0 Output current (mA) 50 50 0 Output voltage (V) 11/27 Electrical characteristics TS1871-TS1872-TS1874 Figure 25. Gain and phase vs. frequency 70 60 50 Gain (dB) 40 30 20 10 0 1E+3 RL = 10K CL = 100 pF Vcc = 1.8V 180 160 140 Figure 26. Gain and phase vs. frequency 70 60 50 Gain (dB) Phase () Phase () 180 RL = 10K CL = 100 pF Vcc = 3V 160 140 Phase () Phase () 120 phase 100 80 60 40 1E+4 1E+5 1E+6 Frequency (Hz) gain 120 phase 100 80 60 40 1E+4 1E+5 Frequency (Hz) 1E+6 40 30 20 10 gain 0 1E+3 Figure 27. Gain and phase vs. frequency 70 60 50 Gain (dB) 40 gain 30 20 10 0 1E+3 phase 100 80 60 40 1E+4 1E+5 1E+6 Frequency (Hz) RL = 10K CL = 100 pF Vcc = 5V 180 Figure 28. Gain bandwidth product vs. temperature 1.70 Vcc = 5V Gain-bandwidth product (MHz) Vicm = Vcc/2 RL = 10kohms CL = 100 pF 160 140 Phase () Phase () 120 1.60 Vcc = 3V 1.50 Vcc = 1.8V 1.40 1.30 1.20 -40 -20 0 20 40 60 80 100 120 140 Temperature (C) Figure 29. Gain bandwidth product vs. supply Figure 30. Slew rate vs. temperature voltage 2.0 Gain bandwidth product (MHz) 0.55 Vcc = 1.8V gain = +1 Vin = 0.4 to 1.4V RL = 10kohm CL = 100 pF negative slew rate 0.50 Slew rate (V/s) 1.5 RL = 2 kohms CL = 220 pF Vicm = Vcc/2 T = 25C positive slew rate 0.45 0.40 1.0 0.35 0.5 1 2 3 4 Supply voltage (V) 5 0.30 -40 -20 0 20 40 60 80 100 120 140 Temperature (C) 12/27 TS1871-TS1872-TS1874 Electrical characteristics Figure 31. Slew rate vs. temperature 0.70 0.65 0.60 Slew rate (V/s) 0.55 0.50 0.45 0.40 0.35 -40 Vcc = 3V gain = +1 Vin = 1 to 2V RL = 10kohm CL = 100 pF positive slew rate Figure 32. Slew rate vs. temperature 0.75 0.70 0.65 Slew rate (V/s) Vcc = 5V gain = +1 Vin = 2 to 3V RL = 10kohms CL = 100 pF positive slew rate negative slew rate 0.60 0.55 0.50 0.45 0.40 0.35 -40 negative slew rate -20 0 20 40 60 80 100 120 140 -20 0 20 40 60 80 100 120 140 Temperature (C) Temperature (C) Figure 33. Phase margin vs. load capacitor 60 50 Phase margin () 40 30 20 10 0 -10 10 100 Load capacitor (pF) 1000 Vcc = 1.8V gain = 40dB RL = 1Kohm Figure 34. Phase margin vs. output current 80 75 Phase margin () 70 65 60 55 50 45 40 -10 Vcc = 1.8V RL = 1 kOhm CL = 220 pF -5 0 DC output current (mA) 5 10 Figure 35. Gain margin vs. output current 0 Figure 36. Equivalent input noise vs. frequency 35 Equivalent input noise (nV/sqrt(Hz)) 30 25 20 15 10 5 1E+1 Vcc = 1.8V gain = 100 Rs = 100 ohms GainmMargin (dB) -5 Vcc = 1.8V RL = 1 kOhm CL = 220 pF -10 -15 -20 -25 -10 -5 0 5 DC output current (mA) 10 1E+2 1E+3 Frequency (Hz) 1E+4 1E+5 13/27 Electrical characteristics TS1871-TS1872-TS1874 Figure 37. Distortion vs. output voltage 100.000 RL= 1Kohms Gain = -1 F = 1000 Hz Vcc = 1.8V Figure 38. Distortion vs. output voltage 100.000 RL= 1Kohms Gain = -1 F = 1000 Hz Vcc = 3V 10.000 Distortion (%) 10.000 Distortion (%) 1.000 1.000 0.100 0.100 0.010 0.010 0.001 0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0080 0.001 0.00 0.20 0.40 0.60 0.80 1.00 1.20 Output voltage (VRMS) Output voltage (VRMS) Figure 39. Distortion vs. output voltage 100.000 RL= 1Kohms Gain = -1 F = 1000 Hz Vcc = 5V Figure 40. Distortion vs. output voltage 100.000 RL= 150 ohms Gain = -1 F = 1000 Hz Vcc = 2.7V 10.000 Distortion (%) 10.000 1.000 Distortion (%) 1.000 0.100 0.100 0.010 0.010 0.001 0.00 0.50 1.00 1.50 2.00 0.001 0.00 0.20 0.40 0.60 0.80 1.00 1.20 Output voltage (VRMS) Output voltage (VRMS) Figure 41. Distortion vs. output voltage 100.000 RL= 1500 ohms Gain = -1 F = 1000 Hz Vcc = 2.7V Figure 42. Distortion vs. output voltage 100.000 RL= 4700 ohms Gain = -1 F = 1000 Hz Vcc = 2.7V 10.000 Distortion (%) 10.000 Distortion (%) 0.20 0.40 0.60 0.80 1.00 1.20 1.000 1.000 0.100 0.100 0.010 0.010 0.001 0.00 0.001 0.00 0.20 0.,40 0.60 0.80 1.00 1.20 Output voltage (VRMS) Output voltage (VRMS) 14/27 TS1871-TS1872-TS1874 Electrical characteristics Figure 43. Distortion vs. frequency 0.014 Vcc = 1.8V Vout = 1Vpp RL = 1Kohms gain = -1 Figure 44. Distortion vs. frequency 0.015 0.013 0.010 0.007 0.005 0.003 0.000 1E+1 Vcc = 3V Vout = 1Vpp RL = 1Kohms gain = -1 0.012 Distortion (%) 0.010 0.008 0.006 0,004. 1E+1 1E+2 1E+3 Frequency (Hz) 1E+4 1E+5 Distortion (%) 1E+2 1E+3 Frequency (Hz) 1E+4 1E+5 Figure 45. Distortion vs. frequency 0.150 0.125 0.100 0.075 0.050 0.025 0.000 1E+1 Vcc = 1.8V Vout = 1Vpp RL = 32 ohms gain = -1 Figure 46. Distortion vs. frequency 0.150 0.125 0.100 0.075 0.050 0.025 0.000 1E+1 Vcc = 3V Vout = 1Vpp RL = 32 ohms gain = -1 Distortion (%) 1E+2 1E+3 Frequency (Hz) 1E+4 1E+5 Distortion (%) 1E+2 1E+3 Frequency (Hz) 1E+4 1E+5 Figure 47. Output power vs. supply voltage 60 RL = 32 ohms 50 Output power (mW) 1% distortion 40 30 0.1% distortion 20 10 0 1 2 3 4 5 6 Supply voltage (V) 10% distortion 15/27 Package mechanical data TS1871-TS1872-TS1874 3 Package mechanical data In order to meet environmental requirements, STMicroelectronics offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics trademark. ECOPACK specifications are available at: www.st.com. 16/27 TS1871-TS1872-TS1874 Package mechanical data 3.1 DIP8 package Dimensions Ref. Min. A A1 A2 b b2 c D E E1 e eA eB L 2.92 3.30 0.38 2.92 0.36 1.14 0.20 9.02 7.62 6.10 3.30 0.46 1.52 0.25 9.27 7.87 6.35 2.54 7.62 10.92 3.81 0.115 0.130 4.95 0.56 1.78 0.36 10.16 8.26 7.11 Millimeters Typ. Max. 5.33 0.015 0.115 0.014 0.045 0.008 0.355 0.300 0.240 0.130 0.018 0.060 0.010 0.365 0.310 0.250 0.100 0.300 0.430 0.150 0.195 0.022 0.070 0.014 0.400 0.325 0.280 Min. Inches Typ. Max. 0.210 17/27 Package mechanical data TS1871-TS1872-TS1874 3.2 SO-8 package Dimensions Ref. Min. A A1 A2 b c D H E1 e h L k ccc 0.25 0.40 1 0.10 1.25 0.28 0.17 4.80 5.80 3.80 4.90 6.00 3.90 1.27 0.50 1.27 8 0.10 0.010 0.016 1 0.48 0.23 5.00 6.20 4.00 Millimeters Typ. Max. 1.75 0.25 0.004 0.049 0.011 0.007 0.189 0.228 0.150 0.193 0.236 0.154 0.050 0.020 0.050 8 0.004 0.019 0.010 0.197 0.244 0.157 Min. Inches Typ. Max. 0.069 0.010 18/27 TS1871-TS1872-TS1874 Package mechanical data 3.3 TSSOP8 package Dimensions Ref. Min. A A1 A2 b c D E E1 e k L L1 aaa 0 0.45 0.60 1 0.1 0.05 0.80 0.19 0.09 2.90 6.20 4.30 3.00 6.40 4.40 0.65 8 0.75 0 0.018 0.024 0.039 0.004 1.00 Millimeters Typ. Max. 1.2 0.15 1.05 0.30 0.20 3.10 6.60 4.50 0.002 0.031 0.007 0.004 0.114 0.244 0.169 0.118 0.252 0.173 0.0256 8 0.030 0.039 Min. Inches Typ. Max. 0.047 0.006 0.041 0.012 0.008 0.122 0.260 0.177 19/27 Package mechanical data TS1871-TS1872-TS1874 3.4 MiniSO-8 package Dimensions Ref. Min. A A1 A2 b c D E E1 e K L L1 0 0.40 0.55 0.05 0.78 0.25 0.13 2.90 4.75 2.90 0.10 0.86 0.33 0.18 3.00 4.90 3.00 0.65 6 0.70 0.10 0 0.016 0.022 Millimeters Typ. Max. 1.1 0.15 0.94 0.40 0.23 3.10 5.05 3.10 0.002 0.031 0.010 0.005 0.114 0.187 0.114 0.004 0.034 0.013 0.007 0.118 0.193 0.118 0.026 6 0.028 0.004 Min. Inches Typ. Max. 0.043 0.006 0.037 0.016 0.009 0.122 0.199 0.122 20/27 TS1871-TS1872-TS1874 Package mechanical data 3.5 DIP14 package Dimensions Ref. Min. a1 B b b1 D E e e3 F I L Z 1.27 3.3 2.54 0.050 8.5 2.54 15.24 7.1 5.1 0.130 0.100 0.51 1.39 0.5 0.25 20 0.335 0.100 0.600 0.280 0.201 1.65 Millimeters Typ. Max. Min. 0.020 0.055 0.020 0.010 0.787 0.065 Inches Typ. Max. 21/27 Package mechanical data TS1871-TS1872-TS1874 3.6 SO-14 package Dimensions Ref. Min. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 8.55 5.8 1.27 7.62 4.0 5.3 1.27 0.68 8 (max.) 0.149 0.181 0.019 8.75 6.2 0.35 0.19 0.5 45 (typ.) 0.336 0.228 0.050 0.300 0.157 0.208 0.050 0.026 0.344 0.244 0.1 Millimeters Typ. Max. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.003 Min. Inches Typ. Max. 0.068 0.007 0.064 0.018 0.010 22/27 TS1871-TS1872-TS1874 Package mechanical data 3.7 TSSOP14 package Dimensions Ref. Min. A A1 A2 b c D E E1 e K L 0 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8 0.75 0 0.018 0.024 1 Millimeters Typ. Max. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8 0.030 0.004 0.039 Min. Inches Typ. Max. 0.047 0.006 0.041 0.012 0.0089 0.201 0.260 0.176 A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 23/27 Package mechanical data TS1871-TS1872-TS1874 3.8 SOT23-5 package Dimensions Ref. Min. A A1 A2 b C D E E1 e e1 L L1 k 0 0.400 0.540 8 0 0.890 0.010 0.880 0.300 0.080 2.800 2.100 1.200 1.300 0.950 1.900 0.600 15.75 21.27 8 2.900 0.950 Millimeters Typ. Max. 1.120 0.100 1.020 0.500 0.200 3.040 2.64 1.400 Min. 35.05 0.39 34.65 11.81 3.15 110.26 82.70 47.26 51.19 37.41 74.82 23.63 114.17 37.41 Mils Typ. Max. 44.12 3.94 40.17 19.69 7.88 119.72 103.96 55.13 7110469/A 24/27 TS1871-TS1872-TS1874 Ordering information 4 Table 6. Ordering information Order codes Temperature range Package Packing Tube or tape & reel Tube or tape & reel Tape & reel K172 SOT23-5L (Automotive grade) DIP8 K182 Tape & reel K183 1872IN Tube 1872AIN SO-8 Tube or tape & reel Tube or tape & reel Tape & reel 1872A TSSOP8 (Automotive grade) MiniSO-8 1872Y Tape & reel 872AY K171 Tape & reel K172 DIP14 DIP14 SO-14 Tube Tube Tube or tape & reel Tube or tape & reel Tape & reel 1874AI TSSOP14 (Automotive grade) TS1874Y Tape & reel TS1874AY 1874IN 1874AIN 1874I 1874AI TS1874Y TS1874AY 1874I TSSOP14 1872I 1872AI 1872Y 1872AY 1872I -40C, +125C TSSOP8 Marking 1871I 1871AI 1872Y 1872AY K171 SOT23-5L Part number TS1871ID/IDT SO-8 TS1871IAID/AIDT TS1871IYD/IYDT (1) TS1871IAIYD/AIYDT(1) TS1871ILT TS1871AILT TS1871IYLT (1) (1) SO-8 (Automotive grade) TS1871AIYLT TS1872IN TS1872AIN TS1872ID/IDT TS1872AID/AIDT TS1872IYD/IYDT(1) TS1872AIYD/AIYDT TS1872IPT TS1872AIPT TS1872IYPT(1) TS1872AIYPT(1) TS1872IST TS1872AIST TS1874IN TS1874AIN TS1874ID/IDT TS1874AID/AIDT TS1874IYD/IYDT(1) TS1874AIYD/AIYDT TS1874IPT TS1874AIPT TS1874IYPT(1) TS1874AIYPT(1) (1) (1) SO-8 (Automotive grade) SO-14 (Automotive grade) 1. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q 002 or equivalent. 25/27 Revision history TS1871-TS1872-TS1874 5 Revision history Date 1-Apr-2002 2-Jan-2005 Revision 1 2 First release. Modifications on AMR Table 1 on page 3 (explanation of Vid and Vi limits). Added limits in temperature in Table 3 on page 5, Table 4 on page 6, Table 5 on page 7. Added SVR in Table 5 (SVR parameter removed from Table 3 and Table 4). Added equivalent input voltage noise in Table 3, Table 4, and Table 5. Added Rthjc values in Table 1. Added automotive grade part numbers to order codes table. Moved order codes table to Section 4 on page 25. Updated format of package information. Changes 21-May-2007 4 26/27 TS1871-TS1872-TS1874 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 27/27 |
Price & Availability of TS1874IYPT |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |